Proceedings · Session S-572 · filed November 18, 2026

Lab Technology & MethodsSession paper

Laser-sintered moon dust yields 3.4 MPa bricks, one-seventh of concrete

Arkansas engineers laser-sintered Apollo-derived regolith simulant into binder-free bricks at 3.4 MPa, one-seventh of concrete, a proof of concept with lunar construction ambitions.

By Amara Osei3 min read576 words

Summary

  • Laser powder bed fusion produced binder-free regolith bricks at 3.4 MPa compressive strength, versus about 25 MPa for residential concrete.
  • The team used Lunar Highlands Regolith Simulant derived from Apollo mission regolith samples.
  • A relatively low-power laser sufficed to sinter the simulant into centimeter-scale interlocking blocks.
  • The study, led by Wan Shou with first author Cole McCallum, was published in NPJ Advanced Manufacturing.
Laser-fused moon-dust 'Lego' bricks target extraterrestrial construction
FigureLaser-fused moon-dust 'Lego' bricks target extraterrestrial construction — CristianIS / pixabay

A University of Arkansas team has 3D-printed centimeter-scale interlocking bricks from simulated lunar regolith using nothing but the material itself, achieving a compressive strength of 3.4 megapascals — roughly one-seventh of the approximately 25 MPa typical of residential concrete. The paper, led by mechanical engineering assistant professor Wan Shou, appeared recently in the journal NPJ Advanced Manufacturing, with first author Cole McCallum.

The result matters for payload economics as much as for materials science. Every kilogram launched toward the Moon consumes fuel, which is why earlier regolith-based construction methods that still required an Earth-supplied binding agent never fully solved the cargo problem. The Arkansas approach eliminates that agent entirely. "There's nothing else it's binding to. The regolith powder is binding to itself," McCallum said in a statement released by the university.

How the process works

The team used laser powder bed fusion, a technique normally reserved for metal powders. A laser selectively sinters powder spread across a flat bed; the bed lowers incrementally, fresh powder is added, and the object builds up one fused layer at a time. Instead of metal, the researchers substituted Lunar Highlands Regolith Simulant, a commercially available material formulated from regolith samples collected during the Apollo missions.

A key finding is energy-related: even a relatively low-power laser sufficed to sinter the simulant. That claim deserves scrutiny before anyone budgets for lunar hardware, because the experiments were conducted at Earth gravity and Earth atmosphere-adjacent conditions, not in the vacuum and thermal extremes of the lunar surface. The source does not report the laser's power rating, sintering speed, or the number of blocks tested, which limits any cost extrapolation.

What the numbers do and do not show

The printed blocks fit together like Lego pieces, forming larger structures without mortar or adhesive. That interlocking geometry is the constructive fact here. The unconstructive one is the measured strength: 3.4 MPa against concrete's 25 MPa means a wall built today from these blocks would carry about 13 percent of the load a comparable concrete wall handles.

Shou frames the current figure as an early-stage result. He is confident that further research could make the technology valuable in the Moon's microgravity environment, where loads differ substantially from terrestrial construction. That is a projection, not a measurement, and the pathway from 3.4 MPa to structural adequacy remains unspecified in the published account. Whether strength gains come from process tuning, layer density, or geometry — and what each costs in laser energy — are open questions the paper's summary does not address.

Researchers and mission planners should also note the simulant caveat. Commercial simulants approximate Apollo-sample chemistry, but they do not reproduce lunar regolith's sharp, unweathered particle shapes or its embedded glass aggregates, both of which can alter sintering behavior. A process validated on simulant at centimeter scale is a proof of concept, not a qualified construction method.

For R&D managers tracking in-situ resource utilization portfolios, the work signals that binder-free laser sintering is technically feasible with modest laser power — a meaningful de-risking milestone for additive manufacturing roadmaps targeting extraterrestrial sites. The measured strength gap and the untested lunar-environment variables define the next phase of work. Shou's team will need to demonstrate higher compressive values, larger build volumes, and performance under simulated vacuum and thermal cycling before the bricks graduate from laboratory curiosity to mission architecture.

via newatlas.com (Source)

Filed under

  • lunar-regolith
  • laser-powder-bed-fusion
  • additive-manufacturing
  • in-situ-resource-utilization
  • extraterrestrial-construction
Share this article:

More from Amara Osei

Amara Osei

Show full bio

News editor covering money, funding and market shifts around research and development at Hypothesis Wire.

253 articles

References

  1. Brimstone Targets 60% Cement CO2 Cut From a Single Silicate Rock
  2. DARPA-Funded Caltech Robot Assembles Truss in Orbit, a First for Space Construction
  3. Hemp Composite Hits 24.6 MPa, 92% Below Concrete's Carbon Output
  4. Sandia develops microwave process for spent battery cathode upcycling
  5. ORNL, INL partner to 3D-print and AI-qualify nuclear pressure vessels

« Previous articleNext article »